OC11 Bedside Sleeper
How to Mount It
Mounting the sleeper is easy and can be done alone in under 20 minutes. You have here a video and below the written instructions with images. If you are not sure about something, write to us at care@ocodile.com.
PARTS LIST
Here is a list of the parts of the Bedside Sleeper. When unboxing the product, make sure you have all these parts and contact us if there is anything missing.
-
A. Main Frame & Fabric
-
B. Central supporting Frame with Spring Clips at Both Ends
-
C. 2 Lower Bars with Spring Clips at Both Ends
-
D. Mattress with Removable Cover
-
E. 2 Connection Belts
-
F. Storage Basket
-
G. Mosquito Net
-
H. Carry Case
SETTING REQUIREMENTS
The bedside crib is not compatible with all bed types. Please check the images below to see:
The feet of the bedside sleeper need to slide under the bed. This requires
at least 3.5 inches clearance between the floor and the bed frame.
A bedside sleeper is designed to provide a sleeping area for an infant until he or she begins to push up on hands and knees or approximately 5 months of age. Move your child to another sleeping product when your child reaches this stage
-
Acceptable bed configuration
with mattress, box springs and
frame all in line.
-
Unacceptable bed configuration
with the mattress, box springs not
in line with the frame (such as
platform beds).
ASSEMBLING
This product has two modes: free standing bassinet and co-sleeper mode.
Take out and identify all the parts and then follow these simple steps:
I. Put the frame with the fabric (A)
on the floor, open the legs.
2. Slide the central frame (B) into the small plastic tubes on the legs
3. Slide in the 2 lower bars (C) in the
lower part of the legs.
4. Make sure the button spring clips are
pushed out after finalizing 2 and 3.
5. Using the velcro strips, fasten the fabric to the central frame.
-
6. Turn the extensions inward, to change from swing option to normal (see Swing Option).
7. Attach the storage basket to the lower bars using the velcro on the sides of the basket.
-
8. Place the mattress in the bassinet.
9. Extend the feet for maximum stability.
Swing Option
At the bottom of the legs, there are 2 long plastic extensions which might arrive turned underneath the feet. In this setting, only the extensions touch the floor and this allows you to swing the crib. Only use this option in the bassinet mode. When first setting the crib, turn the extensions inward.
Converting to swing should be done by an adult while the baby is not inside the bassinet. Never leave the baby alone while in the swing option.
Converting to co-sleeper mode
To convert it to the co-sleeper mode continue with the following steps:
10. Fully unzip both zippers on the front.
11. Pull the gray handle away from the upper bar.
Repeat this on the other side.
12. Lower down the detachable side.
The remaining rail has an enclosed
PE board.
13. Move the bassinet close to the parent's bed.
14. Adjust the height of the crib (see "Height Adjustment") so the upper
part of the rail is NO HIGHER than the adult bed mattress. Both legs
should be adjusted to the same height.
15. Use the belts to attach the bedside sleeper to the adult bed.
(see "Attachment System"). Never use the bedside crib in the co-sleeper
mode without it being properly attached to the adult bed.
The bedside sleeper should be positioned next to the long side of the bed.
HEIGHT ADJUSTMENT
There are 6 height adjustments: from 34 cm (position 6) to 50 cm (position I) from floor to the bottom of the bassinet.
To adjust the height, hold the adjusting levers on both right and left sides and pull them up or push them down, lifting or lowering the bassinet.
Both sides should have the same position or have a maximum difference of 2 positions in the bassinet mode with the head of the baby on the upper part.
ATTACHMENT SYSTEM
Secure the bassinet to your bedframe using the belts as follows:
- There are two pairs of female buckles which are
located on the underside of the bassinet on the
central frame (B).
- Buckle the female clip that has a longer strap
to one of the male clips on the belt. Grab the
male clip at the other side of the belt, take it
around your bed frame and buckle it to the
female buckle with the short strap on the
frame. Adjust the length of the strap of the
belt to ensure a tight fit.
- Repeat this for the other pair of clips.
USAGE
To move the crib while in the bassinet mode, raise the left side of the crib, so it leans on the right side where the wheels are located (under the feet). To comply with the state regulations, we are required to warn you about the following:
No matter who uses this product they should know exactly how the bedside
sleeper works.
Never leave the child unattended in the crib when it's in the bedside
co-sleeper mode with the side open.
Only adults should assemble, anchor or adjust the position of the
bedside sleeper.
The product must always be placed on a horizontal surface.
Never leave the product on an inclined surface with the child inside of it.
Children must not be permitted to play without supervision near the product.
Do not use other mattress than the provided one.
Do not leave any object inside the product that could reduce its depth.
Do not position the bassinet near walls and obstacles to prevent
choking hazards.
FALL HAZARD
To help prevent falls, do not use this product when the infant begins to push up on hands and knees or has reached 9kg, whichever comes first.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.
If a sheet is used with the pad, use only the one provided by the bassinet or cradle manufacturer or one specifically designed to fit the dimension of the bassinet or cradle mattress.
WARNINGS!
SUFFOCATION HAZARD
Infants have suffocated:
- In gaps between extra padding and side of the bassinet/cradle, and
- On soft bedding
Use only the pad provided by manufacturer.
NEVER add a pillow, comforter, or another mattress for padding.
Strings can cause strangulation! Do not place items with a string around a child's neck, such as hood strings or pacifier cords.
Do not suspend strings over a bassinet or cradle or attach strings to toys.
Make sure the product is far away from open fires and other sources of strong heat, such as stoves, heaters or other hazards.
ENTRAPMENT HAZARD
-To prevent death from entrapment, bedside sleeper must be properly secured to adult bed using the attachment system.
-There must be no more than 1/2 in. (13 mm) gap between bedside sleeper and adult bed.
-Check tightness before each use by pulling bedside sleeper in a direction from adult bed.
-If gap exceeds 1/2 in. (13 mm), DO NOT use product. Do not fill the gap with pillows, blankets or other items that are suffocation hazards.
Assemble product according to manufacturer's instructions for ANY use mode
- bedside sleeper as well as the bassinet.